Level of water from which depths displayed on a nautical chart are measured
U.S. civil and maritime uses of tidal data
A chart datum is the water level surface serving as origin of depths displayed on a nautical chart and for reporting and predicting tide heights. A chart datum is generally derived from some tidal phase, in which case it is also known as a tidal datum.[1] Common chart datums are lowest astronomical tide (LAT)[1] and mean lower low water (MLLW). In non-tidal areas, e.g. the Baltic Sea, mean sea level (MSL) is used.[2]
A chart datum is a type of vertical datum and must not be confused with the horizontal datum for the chart.
The following tidal phases are commonly used in the definition of chart datums.
Lowest and highest astronomical tide
Lowest astronomical tide (LAT) is defined as the lowest tide level which can be predicted to occur under average meteorological conditions and under any combination of astronomical conditions.[3]
Many national charting agencies, including the United Kingdom Hydrographic Office and the Australian Hydrographic Service,[4] use the LAT to define chart datums.
One advantage of using LAT for chart datums is that all predicted tidal heights must then be positive (or zero) avoiding possible ambiguity and the need to explicitly state sign.
Calculation of the LAT only allows for gravitational effects so lower tides may occur in practice due to meteorological effects, such as high pressure systems.[5][6]
The highest astronomical tide (HAT) can be defined similarly.
Mean high water
Mean high water (MHW) is the average of all the daily tidal high water levels observed over a period of several years. It is not the same as the normal tidal limit. In the United States this period spans 19 years and is referred to as the National Tidal Datum Epoch.[7]
In Australia, the definition of the MHW is '...the line of the medium high tide between the highest tide of each
lunar month (the springs) and the lowest each lunar month (the Neaps) averaged over the year.'[8]
Mean water
Mean lower low water
Mean lower low water (MLLW) is the average height of the lowest tide recorded at a tide station each day during a 19-year recording period, known as the National Tidal Datum Epoch as used by the United States' National Oceanic and Atmospheric Administration.[9] MLLW is only a mean, so some tidal levels may be negative relative to MLLW; see also #Mean low water springs. The 19-year recording period is the nearest full year count to the 18.6-year cycle of the lunar node regression, which has an effect on tides.[10]
Lower low water large tide
This is an average of lowest low waters taken over a fixed period of tidal predictions, as opposed to actual observations. This is the datum used for coastal charts published by the Canadian Hydrographic Service,[11] with the average taken from 19 years of tidal predictions.[12]
Mean higher high water
Similarly, the mean higher high water (MHHW) is the average height of the highest tide recorded at a tide station each day during the recording period. It is used, among other things as a datum from which to measure the navigational clearance, or air draft, under bridges.
Mean water spring
Spring tides are those when the moon is in a direct alignment with the sun (thus new or full) and in many extra-tropics places when its declination is 23.5°, its maximum.[13] In equatorial, tropical seas, such as the Banda Sea such tides (bulges) occur when there is such an alignment and the declination of the moon is more towards its 0° average, thus more overhead or antiposed.
Mean low water springs
Mean low water springs (MLWS) is the average of the water levels of each pair of successive low waters during that period of about 24 hours in each semi-lunation (approximately every 14 days), when the tidal range is greatest (spring range).[14][15]
Mean high water springs
Mean high water springs (MHWS) is the averaged highest level that spring tides reach over many years (often the last 19 years). Within this, to ensure anomalous levels are tempered, at least two successive high waters during the highest-tide 24 hours are taken.[15]
Such a local level is generally close to the "high water mark" where debris accumulates on a tidal shore on about two days six months apart (and nearby days) annually.
The levels are local as some places are nearer to or form places of almost no tides in and around each ocean (amphidromic points).
Tide tables give the height of the tide above a chart datum making it feasible to calculate the depth of water at a given point and at a given time by adding the charted depth to the height of the tide. One may calculate whether an area that dries is under water by subtracting the drying height from the [given] height calculated from the tide table.
Using charts and tables not based on the same geodetic datum can result in incorrect calculation of water depths.
^ RESOLUTIONS of the INTERNATIONAL HYDROGRAPHIC ORGANIZATION Publication M-3 2nd Edition - 2010 Updated to December 2016. SECTION 2.2 – TIDES AND WATER LEVELS para 2 note (i)
^Australian Tides Manual SP9 V4.1, Australian Intergovernmental Committee on Surveying and Mapping, Permanent Committee on Tides and Mean Sea Level
