This is a Fluidyne variant with a solid displacer piston (3). In figure -a-, as the displacer moves from the cold compression space (2), to the hot expansion space (4) in figure -b-, the temperature of the gaseous working fluid is increased. This increases the pressure of the gaseous working fluid, and as it expands, work is done on the (red) liquid piston as it is pushed through the tube.
schematic of a U-tube type Fluidyne engine.
A concentric-cylinder Fluidyne pumping engine. Topologically equivalent to a U-tube design.

A Fluidyne engine is an alpha or gamma type Stirling engine with one or more liquid pistons. It contains a working gas (often air), and either two liquid pistons or one liquid piston and a displacer.[1]

The engine was invented in 1969.[2] The engine was patented in 1973 by the United Kingdom Atomic Energy Authority.[3][2]

Engine operation

Working gas in the engine is heated, and this causes it to expand and push on the water column. This expansion cools the air which contracts, at the same time being pushed back by the weight of the displaced water column. The cycle then repeats.

The U-tube version has no moving parts in the engine other than the water and air, although there are two check valves in the pump. This engine operates at a natural resonance cycle that is "tuned" by adjusting the geometry, generally with a "tuning tube" of water.

Engine as a pump

In the classic configuration, the work produced via the water pistons is integrated with a water pump. The simple pump is external to the engine, and consists of two check valves, one on the intake and one on the outlet. In the engine, the loop of oscillating liquid can be thought of as acting as a displacer piston. The liquid in the single tube extending to the pump acts as the power piston. Traditionally the pump is open to the atmosphere, and the hydraulic head is small, so that the absolute engine pressure is close to atmospheric pressure.[2][4][5]

Demonstration video

Test of a model Fluidyne engine.
Detail of a water level displacement in a leftmost vertical tube.

The videos show operation of a U-tube type model Fluidyne engine. Hot pipe is heated by a heat gun, and water column oscillation builds up to a steady-state level. Second video shows a detail of the actual water displacement.

See also

References

  1. ^ Romanelli, Alejandro (2019). "The Fluidyne engine". American Journal of Physics. 87 (1). American Association of Physics Teachers (AAPT): 33–37. arXiv:1812.11100. Bibcode:2019AmJPh..87...33R. doi:10.1119/1.5078518. ISSN 0002-9505. S2CID 119221418.
  2. ^ a b c West, C. D. (August 1987). "Stirling Engines, and Irrigation Pumping" (PDF). Oak Ridge National Laboratory. Archived from the original (PDF) on May 24, 2011. Retrieved August 6, 2011. This report was prepared in support of the Renewable Energy Applications and Training Project that is sponsored by the U.S. Agency for International Development for which ORNL provides technical assistance. It briefly outlines the performance that might be achievable from various kinds of Stirling-engine-driven irrigation pumps. Some emphasis is placed on the very simple liquid-piston engines that have been the subject of research in recent years and are suitable for manufacture in less well-developed countries. In addition to the results quoted here (possible limits on M4 and pumping head for different-size engines and various operating conditions), the method of calculation is described in sufficient detail for engineers to apply the techniques to other Stirling engine designs for comparison. [1]
  3. ^ GB1329567 (A) - STIRLING CYCLE HEAT ENGINES
  4. ^ West, C. D. (1983). Liquid piston Stirling engines. New York: Van Nostrand Reinhold. pp. 7. ISBN 978-0-442-29237-9.
  5. ^ Swift, G. (1999). Thermoacoustics: A unifying perspective for some engines and refrigerators. p. 300. ISBN 978-0-735-40065-8.

Further reading

External links

Wikimedia Commons has media related to Fluidynes.
Heat engines
Categories