A schematic of isobaric labeling: proteins are extracted from different conditions or cell types, digested into peptides, and labeled with isobaric stable isotope tags. These tags consist of reporter, balance, and reactive regions. Lighter reporter regions are paired with heavier balance regions, such that the entire tag attached to the peptide adds the same mass shift. Therefore, after mixing, in MS1, the peptides appear as a single precursor. However, when fragmented during MS2, in addition to the normal fragment ions, the reporter regions dissociate to produce ion signals which provide quantitative information regarding the relative amount of the peptide in the samples.
Isobaric labeling is a mass spectrometry strategy used in quantitative proteomics. Peptides or proteins are labeled with chemical groups that have (at least nominally) identical mass (isobaric), but vary in terms of distribution of heavy isotopes in their structure. These tags, commonly referred to as tandem mass tags, are designed so that the mass tag is cleaved at a specific linker region upon high-energy CID (HCD) during tandem mass spectrometry yielding reporter ions of different masses. The most common isobaric tags are amine-reactive tags.[1] However, tags that react with cysteine residues and carbonyl groups have also been described.[2] These amine-reactive groups go through N-hydroxysuccinimide (NHS) reactions, which are based around three types of functional groups.[2] Isobaric labeling methods include tandem mass tags (TMT), isobaric tags for relative and absolute quantification (iTRAQ), mass differential tags for absolute and relative quantification, and dimethyl labeling.[1] TMTs and iTRAQ methods are most common and developed of these methods.[1] Tandem mass tags have a mass reporter region, a cleavable linker region, a mass normalization region, and a protein reactive group and have the same total mass.[3]
Workflow
A typical bottom-up proteomics workflow is described by (Yates, 2014).[2] Protein samples are enzymatically digested by a protease to produce peptides. Each digested experimental sample is derivative with a different isotopic variant of the tag from a set. The samples are mixed in typically equal ratios and analyzed simultaneously in one MS run. Since the tags are isobaric and have identical chemical properties, the isotopic variants of the tags appear as a single composite peak at the same m/z value in an MS1 scan with identical liquid chromatography (LC) retention times. During the MS2 analysis and upon fragmentation, each isotopic variant of the tag produces sequence-specific product ions. These product ions are used to determine the peptide sequence and the reporter tags whose abundances reflect the relative ratio of the peptide in the samples that were combined. The use of MS/MS is required to detect the tags, therefore, unlabeled peptides are not quantified.
Isobaric labeling proteomic workflow with 4 unique reagents in a set, and 7 different biological samples combined into 2 labeling groups (plexes). As the number of samples is higher than the number of reagents, the labeling should be performed in two batches.
Advantages
Explained previously by (Lee, Choe, Aggarwal, 2017).[4] A key benefit of isobaric labeling over other quantification techniques (e.g. label-free) is the multiplex capabilities and thus increased throughput potential. The ability to combine and analyze several samples simultaneously in one LC-MS run eliminates the need to analyze multiple data sets and eliminates run-to-run variation. Multiplexing reduces sample processing variability, improves specificity by quantifying the peptides from each condition simultaneously, and reduces turnaround time for multiple samples. Without multiplexing, information can be missed from run-to-run, affecting identification and quantification, as peptides selected for fragmentation on one LC-MS/MS run may not be present or of suitable quantity in subsequent sample runs. The current available isobaric chemical tags facilitate the simultaneous analysis of 2 to 11 experimental samples.
Applications
ITRAQ 8plex kit
Isobaric labeling has been successfully used for many biological applications including protein identification and quantification, protein expression profiling of normal vs abnormal states, quantitative analysis of proteins for which no antibodies are available and identification and quantification of post translationally modified proteins.[4]
^ abcBantscheff, Marcus; Lemeer, Simone; Savitski, Mikhail M.; Kuster, Bernhard (2012-09-01). "Quantitative mass spectrometry in proteomics: critical review update from 2007 to the present". Analytical and Bioanalytical Chemistry. 404 (4): 939–965. doi:10.1007/s00216-012-6203-4. ISSN1618-2650. PMID22772140. S2CID21085313.
