You do not have permission to edit this page, for the following reasons:

This IP address has been blocked from editing Wikipedia.
This does not affect your ability to read Wikipedia pages.
Most people who see this message have done nothing wrong. Some kinds of blocks restrict editing from specific service providers or telecom companies in response to recent abuse or vandalism, and can sometimes affect other users who are unrelated to that abuse. Review the information below for assistance if you do not believe that you have done anything wrong.

The IP address or range 3.91.0.0/16 has been blocked (disabled) by ‪L235‬ for the following reason(s):

The IP address that you are currently using has been blocked because it is believed to be a web host provider or colocation provider. To prevent abuse, web hosts and colocation providers may be blocked from editing Wikipedia.
You will not be able to edit Wikipedia using a web host or colocation provider because it hides your IP address, much like a proxy or VPN.
We recommend that you attempt to use another connection to edit. For example, if you use a proxy or VPN to connect to the internet, turn it off when editing Wikipedia. If you edit using a mobile connection, try using a Wi-Fi connection, and vice versa. If you are using a corporate internet connection, switch to a different Wi-Fi network. If you have a Wikipedia account, please log in.
If you do not have any other way to edit Wikipedia, you will need to request an IP block exemption.

How to appeal if you are confident that your connection does not use a colocation provider's IP address:
If you are confident that you are not using a web host, you may appeal this block by adding the following text on your talk page: ((unblock|reason=Caught by a colocation web host block but this host or IP is not a web host. My IP address is _______. Place any further information here. ~~~~)). You must fill in the blank with your IP address for this block to be investigated. Your IP address can be determined here. Alternatively, if you wish to keep your IP address private you can use the unblock ticket request system. There are several reasons you might be editing using the IP address of a web host or colocation provider (such as if you are using VPN software or a business network); please use this method of appeal only if you think your IP address is in fact not a web host or colocation provider.

Administrators: The IP block exemption user right should only be applied to allow users to edit using web host in exceptional circumstances, and requests should usually be directed to the functionaries team via email. If you intend to give the IPBE user right, a CheckUser needs to take a look at the account. This can be requested most easily at SPI Quick Checkuser Requests. Unblocking an IP or IP range with this template is highly discouraged without at least contacting the blocking administrator.

This block will expire on 21:36, 3 July 2026.

Even when blocked, you will usually still be able to edit your user talk page, as well as email administrators and other editors.

For information on how to proceed, please read the FAQ for blocked users and the guideline on block appeals. The guide to appealing blocks may also be helpful.

Other useful links: Blocking policy · Help:I have been blocked
Your IP address is in a range that has been blocked on all Wikimedia Foundation wikis. The block was made by ‪Wiki13‬. The reason given is Open proxy/Webhost: Visit the FAQ if you are affected .
- Start of block: 13:43, 5 May 2022
- Expiry of block: 13:43, 5 May 2024
Your current IP address is 3.91.25.123. The blocked range is 3.91.0.0/16. Please include all above details in any queries you make. If you believe you were blocked by mistake, you can find additional information and instructions in the No open proxies global policy. Otherwise, to discuss the block please post a request for review on Meta-Wiki. You could also send an email to the stewards VRT queue at stewards@wikimedia.org including all above details.

You can view and copy the source of this page:

((ref improve|date=March 2014))
'''MPT 1327'''<ref>((Cite web|url=http://www.ofcom.org.uk/static/archive/ra/publication/mpt/mpt_pdf/mpt1327.pdf|title = Regulator archives|date = 16 September 2016))</ref> is an industry standard for [[Trunked Radio Systems|trunked radio communications networks]].

First published in January 1988 by the British [[Radiocommunications Agency]], and is primarily used in the United Kingdom, Europe, South Africa, New Zealand, Australia and even China. Many countries had their own version of numbering/user interface, including [[MPT1343]] in the UK, [[Chekker (communications)|Chekker]] (Regionet 43) in Germany, [[3RP]] (CNET2424) in France, [[Multiax]] in Australia, and [[Gong An]] in China.

MPT systems are still being built in many areas of the world, due to their cost-effectiveness. 

== Digital alternatives ==
The [[TETRA]] trunked radio standard was developed by the [[European Telecommunications Standards Institute]] (ETSI), as a digital alternative to analogue trunked systems.  However, TETRA, with its enhanced [[encryption]] capability, has developed into a higher tier ([[public safety]]) product, currently mainly used by governments, some larger airports and government-owned utilities.  

DMR ([[digital mobile radio]]), and dPMR ([[digital private mobile radio]]) are more recent ETSI-standards for digital mobile radio using two-slot [[time division multiple access|TDMA]] and [[FDMA]] respectively. The Tier 3 standard for these systems defines a trunking protocol very similar to MPT1327 and is intended as a potential migration path for existing and perhaps future trunking customers. Tier 3 equipment is (late 2011) now becoming available, so the impact on TETRA and MPT 1327 is yet to be seen, but may well be significant. However, it is unlikely that in terms of cost that the complicated new DMR/dPMR equipment will be able to compete with the simpler MPT1327 equipment for some time, if ever.

It is worth noting that whilst many comparisons are made between Digital and Analog radio technologies, when it comes to applying these arguments to MPT1327, many of the distinctions become blurred, since MPT1327 with its digital control channel, already offers most of the features being offered by the DMR/dPMR/TETRA counterparts.

Furthermore, most MPT1327 systems are engineered to a far higher standard than conventional FM systems, partially due to the lack of CTCSS within the standard. As such arguments with regards to "noisy FM audio quality", can become misleading, since the squelch levels tend to be set rather high on MPT1327 systems, such that weak/noisy signals do not generally open the mute.

==MPT1327 advantages and features==
The advantage of MPT 1327 over TETRA is the increased availability, lower cost of equipment, the ease of installation, the familiarity with the equipment, and many believe that MPT 1327 is superior to TETRA, due to its uncompressed FM audio, and greater receiver sensitivity. MPT1327 control channel signalling is more resilient, since the TETRA protocol uses a complex [[modulation]] scheme that requires a far higher Signal to Noise ratio to function than 1,200 bit/s [[FFSK]] signalling.

Systems based on MPT 1327 only require one, but usually use two or more radio channels per site. Channels can be 12.5 or 25 kHz bandwidth, and can be any variety of channel spacings, with 6.25 kHz or 12.5 kHz being typical. At least one of these channels is defined as the control channel (CCH) and all other channels are traffic channels (TCs) used for speech calls.

A typical installation will have around 6–10 channels. A 7-channel trunk, correctly engineered, is capable of handling in excess of 3,000 mobile units. The capacity of the system increases dramatically with the number of traffic channels. For example, 1 traffic channel with queuing can not handle many customers, perhaps 2 [[minicab]]s with 20 mobiles. In effect this would be a CBS with queuing. However, a 7 channel trunked system can handle 40 minicabs with 20 mobiles with ease. The [[Erlang (unit)|Erlang]] formulas are typically used for calculating system capacity.

===Spectrum efficiency===
Whilst MPT 1327 systems, unlike DMR or dPMR, do not employ digital speech compression to gain any Spectral Efficiency (voice channels per 6.25 kHz), there are several methods used that increase the Spectrum Efficiency (Erlangs per square kilometre, per 6.25 kHz).

A spectrum efficiency advantage over a 4-slot TDMA system like TETRA is in areas where low-bandwidth channels are required.  The absolute minimum TETRA installation would require a 25 kHz bandwidth in order to carry a control slot and three traffic slots. The absolute minimum MPT1327 assignment is a single non-dedicated control channel, utilising 12.5 kHz, in most cases.

A non-dedicated control channel can be used as a traffic channel when all the other traffic channels are busy. This can be useful if the site is part of a multi-site network and has a very low traffic profile as the site could have a single channel rather than at least two freeing up one channel for use elsewhere.  The disadvantage is loss of queuing, and data cannot be sent on the control channel whilst it is in traffic mode. A non-dedicated CCH should not be used as a "reserve tank" for a busy site as the lack of signalling will seriously affect the operation of the site.  

====Time-shared control channels and channel pooling====

Some MPT 1327 networks can also time-share control channels, which can be useful if the network has limited frequency availability, as it frees up channels for use as traffic channels, which can also be pooled across sites so the network capacity follows the traffic.  This is another advantage of MPT 1327 (and dPMR) over TDMA-based systems such as TETRA and DMR, which cannot pool traffic channels so efficiently (if at all).  The disadvantage of using a time-shared CCH is that it slows down registration and calls and requires some customization of the registration process, so is only useful if the network has a patient user community!

====Control channel cycling====

The control channel can also be set to cycle, so each channel in turn becomes a control channel, say every ten minutes it will change. The advantage of this is that the base does not have to be rated at 100% duty cycle and does not get so hot. However, this can cause problems with queuing, affects registration and control channel acquisition times. Most base stations have a 100% duty-cycle rating, but this function can be useful if local Regulatory rules do not permit Continuous CCH operation.  In countries where dedicated channels for trunked systems are not possible or availability is limited it is also possible to actively manage the use of traffic channels based on co-channel use, i.e. to avoid interfering with other users by using "friendly" channel acquisition protocols.

===Speech and data===
Speech is sent as [[narrowband]] [[frequency modulation]]. Data messages between mobiles and the network are exchanged on the control channel at 1,200 bits per second using FFSK signalling, or a specific "modem call", known as "non-prescribed data" can be established, whereby free-form 1,200 baud data can be exchanged on a traffic channel without tying up the control channel. With the use of special modems, the speed can be 19,200 bit/s. This, along with Short Data Messaging and Status Messaging via the control channel makes an MPT1327 network ideal for managing [[automatic vehicle location|AVL for asset management]], [[automatic meter reading|meter reading]] and [[SCADA]] networks, the advantage being that the network can be used for this sort of application whilst still carrying voice traffic. 

===Numbering===
Each subscriber in an MPT-1327 trunked radio network has a unique call number. This call number (address) is a compound number consisting of a prefix (three digits), the fleet number and the subscriber's call number within the fleet. Different numbering schemes work differently, for example [[Zetron]] uses the first two digits of the Ident as the fleet number, and the last two digits as the unit number. Idents in the 6,000–6,999 range are typically used to establish group calls. After it has been entered the call number will be converted in the mobile to a 20-bit address. The numbering rules are clarified and expanded by supplementary standards such as MPT-1343.

For the duration of his call a subscriber is exclusively allocated a traffic channel from the available pool. If all channels are occupied, the call will be queued. If the control channel has become a traffic channel, like in the case of a non-dedicated control channel, the call will be queued in the radio, although radio queuing loses the first come, first served effect, so if there are seven units queuing, the last unit to queue may get a traffic channel first.

==The different types of communications on an MPT-1327 network and their definitions==

===Traffic types===

* Mobile-mobile in a cell
* Mobile-mobile in different cells
* Mobile-line access unit via [[landline]] or radio
* Mobile-[[dispatcher]] station via landline or radio
* Mobile-[[PABX]], Mobile-[[PSTN]]

===Data communication===

* Status messages on the control channel (5-bit data length)
* Short data messages on the control channel (186-bit data length) 
* Transparent data transmission on the TC (data communication).

===Calls===

* Point to point connections
* Group calls with talk entitlement
* Group calls without talk entitlement (broadcast calls)

Broadcast calls can be used to make announcements to the entire customer base on a trunked system. For example, if work is to be carried out on the trunked system, the owner of the system can initiate a Broadcast Call which calls every mobile on the system. However, the mobiles may not have talk entitlement, so the PTT may not work. By this means the owner can announce to all customers a short period of inoperation due to maintenance.

==Notes==
((reflist))

((Trunked radio systems))

[[Category:Trunked radio systems]]
[[Category:Mobile telecommunications standards]]

Pages transcluded onto the current version of this page (help):

MPT-1327 (edit)
Template:Ambox (view source) (template editor protected)
Template:Cite web (view source) (protected)
Template:Find sources mainspace (view source) (template editor protected)
Template:Hlist/styles.css (view source) (protected)
Template:Main other (view source) (protected)
Template:More citations needed (view source) (template editor protected)
Template:Navbox (view source) (template editor protected)
Template:Ref improve (view source) (template editor protected)
Template:Reflist (view source) (protected)
Template:Reflist/styles.css (view source) (protected)
Template:Trunked radio systems (edit)
Module:Arguments (view source) (protected)
Module:Category handler (view source) (protected)
Module:Category handler/blacklist (view source) (protected)
Module:Category handler/config (view source) (protected)
Module:Category handler/data (view source) (protected)
Module:Category handler/shared (view source) (protected)
Module:Check for unknown parameters (view source) (protected)
Module:Citation/CS1 (view source) (protected)
Module:Citation/CS1/COinS (view source) (protected)
Module:Citation/CS1/Configuration (view source) (protected)
Module:Citation/CS1/Date validation (view source) (protected)
Module:Citation/CS1/Identifiers (view source) (protected)
Module:Citation/CS1/Utilities (view source) (protected)
Module:Citation/CS1/Whitelist (view source) (protected)
Module:Citation/CS1/styles.css (view source) (protected)
Module:Find sources (view source) (template editor protected)
Module:Find sources/config (view source) (template editor protected)
Module:Find sources/links (view source) (template editor protected)
Module:Find sources/templates/Find sources mainspace (view source) (template editor protected)
Module:Message box (view source) (protected)
Module:Message box/ambox.css (view source) (protected)
Module:Message box/configuration (view source) (protected)
Module:Namespace detect/config (view source) (protected)
Module:Namespace detect/data (view source) (protected)
Module:Navbar (view source) (protected)
Module:Navbar/configuration (view source) (protected)
Module:Navbar/styles.css (view source) (protected)
Module:Navbox (view source) (template editor protected)
Module:Navbox/configuration (view source) (template editor protected)
Module:Navbox/styles.css (view source) (template editor protected)
Module:Unsubst (view source) (protected)
Module:Yesno (view source) (protected)

Return to MPT-1327.

Retrieved from "https://en.wikipedia.org/wiki/MPT-1327"