The design comprises a single combined cycle rocket engine with two modes of operation.[3] The air-breathing mode combines a turbo-compressor with a lightweight air precooler positioned just behind the inlet cone. At high speeds this precooler cools the hot, ram-compressed air, which would otherwise reach a temperature that the engine could not withstand,[8] leading to a very high pressure ratio within the engine. The compressed air is subsequently fed into the rocket combustion chamber where it is ignited along with stored liquid hydrogen. The high pressure ratio allows the engine to provide high thrust at very high speeds and altitudes. The low temperature of the air permits light alloy construction to be employed and allow a very lightweight engine—essential for reaching orbit. In addition, unlike the LACE concept, SABRE's precooler does not liquefy the air, letting it run more efficiently.[2]
After shutting the inlet cone off at Mach 5.14, and at an altitude of 28.5 km,[3] the system continues as a closed-cycle high-performance rocket engine burning liquid oxygen and liquid hydrogen from on-board fuel tanks, potentially allowing a hybrid spaceplane concept like Skylon to reach orbital velocity after leaving the atmosphere on a steep climb.
The LACE system was to be placed behind a supersonic air intake which would compress the air through ram compression, then a heat exchanger would rapidly cool it using some of the liquid hydrogen fuel stored on board. The resulting liquid air was then processed to separate the liquid oxygen for combustion. The amount of warmed hydrogen was too great to burn with the oxygen, so most was to be expelled, giving useful thrust, but greatly reducing the potential efficiency.[citation needed]
Instead, as part of the HOTOL project, the liquid air cycle engine (LACE) based RB545 engine was developed with more efficient cycle. The engine was given the Rolls-Royce name "Swallow".[11] In 1989, after funding for HOTOL ceased, Bond and several others formed Reaction Engines Limited to continue research. The RB545's precooler had issues with embrittlement and excess liquid hydrogen consumption, and was encumbered by both patents and the UK's Official Secrets Act, so Bond developed SABRE instead.[12]
In 2016 the project received £60m in funds from the UK government and ESA for a demonstrator involving the full cycle.[13]
In July 2021 the UK Space Agency provided a further £3.9m for continued development.[14]
Concept
Like the RB545, the SABRE design is neither a conventional rocket engine nor a conventional jet engine, but a hybrid that uses air from the environment at low speeds/altitudes, and stored liquid oxygen at higher altitude. The SABRE engine "relies on a heat exchanger capable of cooling incoming air to −150 °C (−238 °F), to provide oxygen for mixing with hydrogen and provide jet thrust during atmospheric flight before switching to tanked liquid oxygen when in space."
In air-breathing mode, air enters the engine through an inlet. A bypass system directs some of the air through a precooler into a compressor, which injects it into a combustion chamber where it is burnt with fuel, the exhaust products are accelerated through nozzles to provide thrust. The remainder of the intake air continues through the bypass system to a ring of flame holders which act as a ramjet for part of the air breathing flight regime. A helium loop is used to transfer the heat from the precooler to the fuel and drive the engine pumps and compressors.
Inlet
At the front of the engine, the concept designs propose a simple translating axisymmetric shock cone inlet which compresses and slows the air (relative to the engine) to subsonic speeds using two shock reflections. Accelerating the air to the speed of the engine incurs ram drag. As a result of the shocks, compression, and acceleration the intake air is heated, reaching around 1,000 °C (1,830 °F) at Mach5.5.
Bayern-Chemie, through ESA, have undertaken work to refine and test the intake and bypass systems[15]
Precooler
As the air enters the engine at supersonic or hypersonic speeds, it becomes hotter than the engine can withstand due to compression effects.[8]Jet engines, which have the same problem but to a lesser degree, solve it by using heavy copper or nickel-based materials, by reducing the engine's pressure ratio, and by throttling back the engine at the higher airspeeds to avoid melting. However, for a single-stage-to-orbit (SSTO) spaceplane, such heavy materials are unusable, and maximum thrust is necessary for orbital insertion at the earliest time to minimise gravity losses. Instead, using a gaseous helium coolant loop, SABRE dramatically cools the air from 1,000 °C (1,830 °F) down to −150 °C (−238 °F) in a counterflow heat exchanger while avoiding liquefaction of the air or blockage from freezing water vapour. The counterflow heat exchanger also allows the helium to exit the engine at a sufficiently high temperature to drive pumps and compressors for the liquid hydrogen fuel and helium working fluid itself.
Previous versions of precoolers such as HOTOL put the hydrogen fuel directly through the precooler. SABRE inserts a helium cooling loop between the air and the cold fuel to avoid problems with hydrogen embrittlement in the precooler.
The dramatic cooling of the air created a potential problem: it is necessary to prevent blocking the precooler from frozen water vapour and other air fractions. In October 2012, the cooling solution was demonstrated for 6 minutes using freezing air.[16] The cooler consists of a fine pipework heat exchanger with 16,800 thin-walled tubes,[17] and cools the hot in-rushing atmospheric air down to the required −150 °C (−238 °F) in 0.01s.[18] The ice prevention system had been a closely guarded secret, but REL disclosed a methanol-injecting 3D-printed de-icer in 2015 through patents, as they needed partner companies and could not keep the secret while working closely with outsiders.[19][20][21]
Compressor
Below five times the speed of sound and 25 kilometres of altitude, which are 20% of the speed and 20% of the altitude needed to reach orbit, the cooled air from the precooler passes into a modified turbo-compressor, similar in design to those used on conventional jet engines but running at an unusually high pressure ratio made possible by the low temperature of the inlet air. The compressor feeds the compressed air at 140 atmospheres into the combustion chambers of the main engines.[22]
In a conventional jet engine, the turbo-compressor is driven by a gas turbine powered by combustion gases. SABRE drives the turbine with a helium loop, which is powered by heat captured in the precooler and a preburner.[22]
Helium loop
The 'hot' helium from the air precooler is recycled by cooling it in a heat exchanger with the liquid hydrogen fuel. The loop forms a self-starting Brayton cycle engine, cooling critical parts of the engine and powering turbines.[citation needed] The heat passes from the air into the helium. This heat energy is used to power various parts of the engine and to vaporise hydrogen, which is then burnt in ramjets.[3][23]
Combustion chambers
The combustion chambers in the SABRE engine are cooled by the oxidant (air/liquid oxygen) rather than by liquid hydrogen[24] to further reduce the system's use of liquid hydrogen compared with stoichiometric systems.
Nozzles
The most efficient atmospheric pressure at which a conventional propelling nozzle works is set by the geometry of the nozzle bell. While the geometry of the conventional bell remains static the atmospheric pressure changes with altitude and therefore nozzles designed for high performance in the lower atmosphere lose efficiency as they reach higher altitudes. In traditional rockets this is overcome by using multiple stages designed for the atmospheric pressures they encounter.
The SABRE engine must operate at both low and high altitude scenarios. To ensure efficiency at all altitudes a sort of moving, Expanding nozzle is used. First at low altitude, air-breathing flight the bell is located rearwards, connected to a toroidal combustion chamber surrounding the top part of the nozzle, together forming an expansion deflection nozzle. When SABRE later transitions into rocket mode, the bell is moved forwards, extending the length of the bell of the inner rocket combustion chamber, creating a much larger, high altitude nozzle for more efficient flight.[25]
Nozzle in Rocket mode
Bypass burners
Avoiding liquefaction improves the efficiency of the engine since less entropy is generated and therefore less liquid hydrogen is boiled off. However, simply cooling the air needs more liquid hydrogen than can be burnt in the engine core. The excess is expelled through a series of burners called "spill duct ramjet burners",[3][23] that are arranged in a ring around the central core. These are fed air that bypasses the precooler. This bypass ramjet system is designed to reduce the negative effects of drag resulting from air that passes into the intakes but is not fed into the main rocket engine, rather than generating thrust. At low speeds the ratio of the volume of air entering the intake to the volume that the compressor can feed to the combustion chamber is at its highest, requiring the bypassed air to be accelerated to maintain efficiency at these low speeds. This distinguishes the system from a turboramjet where a turbine-cycle's exhaust is used to increase air-flow for the ramjet to become efficient enough to take over the role of primary propulsion.[26]
Development
The latest SABRE engine's design.
Tests were carried out in 2008 by Airborne Engineering Ltd on an expansion deflection nozzle called STERN to provide the data needed to develop an accurate engineering model to overcome the problem of non-dynamic exhaust expansion. This research continued with the STRICT nozzle in 2011.
Successful tests of an oxidiser (both air and oxygen) cooled combustion chamber were conducted by EADS-Astrium at Institute of Space Propulsion in 2010
In 2011, hardware testing of the heat exchanger technology "crucial to [the] hybrid air- and liquid oxygen-breathing [SABRE] rocket motor" was completed, demonstrating that the technology is viable.[27][28] The tests validated that the heat exchanger could perform as needed for the engine to obtain adequate oxygen from the atmosphere to support the low-altitude, high-performance operation.[27][28]
In November 2012, Reaction Engines announced it had successfully concluded a series of tests that prove the cooling technology of the engine, one of the main obstacles towards the completion of the project. The European Space Agency (ESA) evaluated the SABRE engine's precooler heat exchanger, and accepted claims that the technologies required to proceed with the engine's development had been fully demonstrated.[27][29][30]
In June 2013 the United Kingdom government announced further support for the development of a full-scale prototype of the SABRE engine,[31] providing £60M of funding between 2014 and 2016[32][33] with the ESA providing an additional £7M.[34] The total cost of developing a test rig is estimated at £200M.[32]
By June 2015, SABRE's development continued with The Advanced Nozzle Project at Westcott. The test engine, operated by Airborne Engineering Ltd., is being used to analyze the aerodynamics and performance of the advanced nozzles that the SABRE engine will use, in addition to new manufacturing technologies such as the 3D-printed propellant injection system.[35]
In April 2015, the SABRE engine concept passed a theoretical feasibility review conducted by the U.S. Air Force Research Laboratory.[36][37][38] The laboratory was to reveal two-stage-to-orbit SABRE concepts shortly afterwards, as they considered that a single-stage-to-orbit Skylon space plane is "technically very risky as a first application of SABRE engine".[39]
In August 2015 the European Commission competition authority approved UK government funding of £50 million for further development of the SABRE project. This was approved on the grounds that money raised from private equity had been insufficient to bring the project to completion.[40] In October 2015 British company BAE Systems agreed to buy a 20% stake in the company for £20.6 million as part of an agreement to help develop the SABRE hypersonic engine.[41][42]
In 2016, Reaction CEO Mark Thomas announced plans to build a quarter-sized ground test engine, given limitations of funding.[43]
In September 2016 agents acting on behalf of Reaction Engines applied for planning consent to build a rocket engine test facility at the site of the former Rocket Propulsion Establishment in Westcott, UK[44] which was granted in April 2017,[45] and in May 2017 a groundbreaking ceremony was held to announce the beginning of construction of the SABRE TF1 engine test facility, expected to become active in 2020.[46][47] However, development of the TF1 facility has since been quietly dropped, and the site has now been taken on by aerospace and defence group Nammo.[48]
In September 2017 it was announced the United States Defence Advanced Research Projects Agency (DARPA) had contracted with Reaction Engines Inc. to build a high-temperature airflow test facility at Front Range Airport near Watkins, Colorado.[49] The DARPA contract is to test the Sabre engine's pre-cooler heat exchanger (HTX). Construction of the test facilities and test articles began in 2018 with testing focusing on running the HTX at temperatures simulating air coming through a subsonic intake travelling at Mach5 or around 1,800 °F (1,000 °C) beginning in 2019.[50][51]
The HTX test unit was completed in the UK and sent to Colorado in 2018, where on 25 March 2019 an F-4 GE J79 turbojet exhaust was mixed with ambient air to replicate Mach3.3 inlet conditions, successfully quenching a 420 °C (788 °F) stream of gases to 100 °C (212 °F) in less than 1/20 of a second. Further tests simulating Mach5 were planned, with temperature reduction expected from 1,000 °C (1,830 °F).[8][17] These further tests were successfully completed by October 2019.[52][53][54]
The successful HTX test could lead to spin-off precooler applications which could be developed before a scalable SABRE demonstrator is completed; suggested uses are to expand gas turbines capabilities, in advanced turbofans, hypersonic vehicles, and industrial applications.[55]
In March 2019, the UKSA and ESA preliminary design review of the demonstrator engine core confirmed the test version to be ready for implementation.[56]
In 2019, Airborne Engineering conducted a test campaign on subscale air/hydrogen injectors for the SABRE preburners.[57]
In 2020, Airborne Engineering conducted a test campaign on an "HX3 module" (preburner to helium loop heat exchanger) [58]
In 2022, a Foreign Comparative Testing of Reaction’s precooler heat exchanger was performed. The testing was successfully completed by the company’s US subsidiary (Reaction Engines Incorporated – REI) and the US Air Force Research Laboratory (AFRL). “The FCT test program greatly expanded the demonstrated capabilities of our engine precooler technology”, said REI’s director of engineering, Andrew Piotti. “During these recent tests, the precooler successfully achieved our objective of over 10 megawatts of transferred thermal energy from the high-temperature airflow, which is three times higher than our previous test program.”[59]
Engine
Due to the static thrust capability of the hybrid rocket engine, the vehicle can take off under air-breathing mode, much like a conventional turbojet.[3] As the craft ascends and the outside air pressure drops, more and more air is passed into the compressor as the effectiveness of the ram compression drops. In this fashion the jets are able to operate to a much higher altitude than would normally be possible.
At Mach5.5 the air-breathing system becomes inefficient and is powered down, replaced by the on-board stored oxygen which allows the engine to accelerate to orbital velocities (around Mach25).[22]
Evolution
RB545
Designed for use with HOTOL.
The engine had no air-breathing static thrust capability, relying on a rocket trolley to achieve takeoff
SABRE
Designed for use with Skylon A4.
The engine had no air-breathing static thrust capability, relying on RATO engines.
SABRE 2
Designed for use with Skylon C1.
The engine had no static thrust capability, using LOX until the air-breathing cycle could take over.[citation needed]
SABRE 3
Designed for use with Skylon C2.
This engine included a fuel rich preburner to augment the heat recovered from the airstream used to drive the helium loop, giving the engine static thrust capability.
SABRE 4
SABRE 4 is no longer a single engine design, but a class of engines, e.g. a 0.8–2 MN (180,000–450,000 lbf; 82–204 tf) instance of this engine is used with SKYLON D1.5, a 110,000–280,000 lbf (0.49–1.25 MN; 50–127 tf) for a USAF study into a partially reusable TSTO.
Performance
The designed thrust-to-weight ratio of SABRE is fourteen compared to about five for conventional jet engines, and two for scramjets.[5] This high performance is a combination of the denser, cooled air, requiring less compression, and, more importantly, the low air temperatures permitting lighter alloys to be used in much of the engine. Overall performance is much better than the RB545 engine or scramjets.
The combination of high fuel efficiency and low-mass engines permits an SSTO approach, with air-breathing to Mach5.14+ at 28.5 km (94,000 ft) altitude, and with the vehicle reaching orbit with more payload mass per take-off mass than just about any non-nuclear launch vehicle ever proposed.[citation needed]
The precooler adds mass and complexity to the system and is the most aggressive and difficult part of the design, but the mass of this heat exchanger is an order of magnitude lower than has been achieved previously. The experimental device achieved heat exchange of almost 1 GW/m3. The losses from carrying the added weight of systems shut down during the closed cycle mode (namely the precooler and turbo-compressor) as well as the added weight of Skylon's wings are offset by the gains in overall efficiency and the proposed flight plan. Conventional launch vehicles such as the Space Shuttle spend about one-minute climbing almost vertically at relatively low speeds; this is inefficient but optimal for pure-rocket vehicles. In contrast, the SABRE engine permits a much slower, shallower climb (thirteen minutes to reach the 28.5 km transition altitude), while breathing air and using its wings to support the vehicle. This trades gravity drag and an increase in vehicle weight for a reduction in propellant mass and a gain from aerodynamic lift increasing payload fraction to the level at which SSTO becomes possible.
A hybrid jet engine like SABRE needs only reach low hypersonic speeds inside the lower atmosphere before engaging its closed cycle mode, whilst climbing, to build speed. Unlike ramjet or scramjet engines, the design is able to provide high thrust from zero speed up to Mach5.4,[4] with excellent thrust over the entire flight, from the ground to very high altitude, with high efficiency throughout. In addition, this static thrust capability means the engine can be realistically tested on the ground, which drastically cuts testing costs.[5]
In 2012, REL expected test flights by 2020, and operational flights by 2030.[60]
.jpg)
