Passband modulation 

Analog modulation 
Digital modulation 
Hierarchical modulation 
Spread spectrum 
See also 
Quadrature amplitude modulation (QAM) is the name of a family of digital modulation methods and a related family of analog modulation methods widely used in modern telecommunications to transmit information. It conveys two analog message signals, or two digital bit streams, by changing (modulating) the amplitudes of two carrier waves, using the amplitudeshift keying (ASK) digital modulation scheme or amplitude modulation (AM) analog modulation scheme. The two carrier waves are of the same frequency and are out of phase with each other by 90°, a condition known as orthogonality or quadrature. The transmitted signal is created by adding the two carrier waves together. At the receiver, the two waves can be coherently separated (demodulated) because of their orthogonality property. Another key property is that the modulations are lowfrequency/lowbandwidth waveforms compared to the carrier frequency, which is known as the narrowband assumption.
Phase modulation (analog PM) and phaseshift keying (digital PSK) can be regarded as a special case of QAM, where the amplitude of the transmitted signal is a constant, but its phase varies. This can also be extended to frequency modulation (FM) and frequencyshift keying (FSK), for these can be regarded as a special case of phase modulation.
QAM is used extensively as a modulation scheme for digital telecommunication systems, such as in 802.11 WiFi standards. Arbitrarily high spectral efficiencies can be achieved with QAM by setting a suitable constellation size, limited only by the noise level and linearity of the communications channel.^{[1]} QAM is being used in optical fiber systems as bit rates increase; QAM16 and QAM64 can be optically emulated with a 3path interferometer.^{[2]}^{[3]}
In a QAM signal, one carrier lags the other by 90°, and its amplitude modulation is customarily referred to as the inphase component, denoted by I(t). The other modulating function is the quadrature component, Q(t). So the composite waveform is mathematically modeled as:

(Eq.1) 
where f_{c} is the carrier frequency. At the receiver, a coherent demodulator multiplies the received signal separately with both a cosine and sine signal to produce the received estimates of I(t) and Q(t). For example:
Using standard trigonometric identities, we can write this as:
Lowpass filtering r(t) removes the high frequency terms (containing 4πf_{c}t), leaving only the I(t) term. This filtered signal is unaffected by Q(t), showing that the inphase component can be received independently of the quadrature component. Similarly, we can multiply s_{c}(t) by a sine wave and then lowpass filter to extract Q(t).
The addition of two sinusoids is a linear operation that creates no new frequency components. So the bandwidth of the composite signal is comparable to the bandwidth of the DSB (DoubleSideband) components. Effectively, the spectral redundancy of DSB enables a doubling of the information capacity using this technique. This comes at the expense of demodulation complexity. In particular, a DSB signal has zerocrossings at a regular frequency, which makes it easy to recover the phase of the carrier sinusoid. It is said to be selfclocking. But the sender and receiver of a quadraturemodulated signal must share a clock or otherwise send a clock signal. If the clock phases drift apart, the demodulated I and Q signals bleed into each other, yielding crosstalk. In this context, the clock signal is called a "phase reference". Clock synchronization is typically achieved by transmitting a burst subcarrier or a pilot signal. The phase reference for NTSC, for example, is included within its colorburst signal.
Analog QAM is used in:
In the frequency domain, QAM has a similar spectral pattern to DSBSC modulation. Applying Euler's formula to the sinusoids in Eq.1, the positivefrequency portion of s_{c} (or analytic representation) is:
where denotes the Fourier transform, and and are the transforms of I(t) and Q(t). This result represents the sum of two DSBSC signals with the same center frequency. The factor of i (= e^{iπ/2}) represents the 90° phase shift that enables their individual demodulations.
As in many digital modulation schemes, the constellation diagram is useful for QAM. In QAM, the constellation points are usually arranged in a square grid with equal vertical and horizontal spacing, although other configurations are possible (e.g. a hexagonal or triangular grid). In digital telecommunications the data is usually binary, so the number of points in the grid is typically a power of 2 (2, 4, 8, …), corresponding to the number of bits per symbol. The simplest and most commonly used QAM constellations consist of points arranged in a square, i.e. 16QAM, 64QAM and 256QAM (even powers of two). Nonsquare constellations, such as CrossQAM, can offer greater efficiency but are rarely used because of the cost of increased modem complexity.
By moving to a higherorder constellation, it is possible to transmit more bits per symbol. However, if the mean energy of the constellation is to remain the same (by way of making a fair comparison), the points must be closer together and are thus more susceptible to noise and other corruption; this results in a higher bit error rate and so higherorder QAM can deliver more data less reliably than lowerorder QAM, for constant mean constellation energy. Using higherorder QAM without increasing the bit error rate requires a higher signaltonoise ratio (SNR) by increasing signal energy, reducing noise, or both.
If datarates beyond those offered by 8PSK are required, it is more usual to move to QAM since it achieves a greater distance between adjacent points in the IQ plane by distributing the points more evenly. The complicating factor is that the points are no longer all the same amplitude and so the demodulator must now correctly detect both phase and amplitude, rather than just phase.
64QAM and 256QAM are often used in digital cable television and cable modem applications. In the United States, 64QAM and 256QAM are the mandated modulation schemes for digital cable (see QAM tuner) as standardised by the SCTE in the standard ANSI/SCTE 07 2013. Note that many marketing people will refer to these as QAM64 and QAM256.^{[citation needed]} In the UK, 64QAM is used for digital terrestrial television (Freeview) whilst 256QAM is used for FreeviewHD.
Communication systems designed to achieve very high levels of spectral efficiency usually employ very dense QAM constellations. For example, current Homeplug AV2 500Mbit/s powerline Ethernet devices use 1024QAM and 4096QAM,^{[4]} as well as future devices using ITUT G.hn standard for networking over existing home wiring (coaxial cable, phone lines and power lines); 4096QAM provides 12 bits/symbol. Another example is ADSL technology for copper twisted pairs, whose constellation size goes up to 32768QAM (in ADSL terminology this is referred to as bitloading, or bit per tone, 32768QAM being equivalent to 15 bits per tone).^{[5]}
Ultrahigh capacity Microwave Backhaul Systems also use 1024QAM.^{[6]} With 1024QAM, adaptive coding and modulation (ACM) and XPIC, vendors can obtain gigabit capacity in a single 56 MHz channel.^{[6]}
In moving to a higher order QAM constellation (higher data rate and mode) in hostile RF/microwave QAM application environments, such as in broadcasting or telecommunications, multipath interference typically increases. There is a spreading of the spots in the constellation, decreasing the separation between adjacent states, making it difficult for the receiver to decode the signal appropriately. In other words, there is reduced noise immunity. There are several test parameter measurements which help determine an optimal QAM mode for a specific operating environment. The following three are most significant:^{[7]}